Sub program

Started by mowens, May 12, 2021, 07:26 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Go Down Pages1

mowens

May 12, 2021, 07:26 AM Last Edit: December 31, 1969, 04:00 PM by Guest
CGTech has asked me to send them a sub program that our machine uses but I can't find it. The control is a heavily modified Fanuc 30i control. I can find a backup copy on the PC side but not the current program. It was well over 20 years ago the last time I delved into the control itself and I'm a little lost.
Any suggestions?
"I would gladly risk feeling bad at times if it also meant that I could taste my dessert." - Data

HTM01

#1
May 12, 2021, 07:37 AM Last Edit: December 31, 1969, 04:00 PM by Guest
it's not like a haas with 9***** programs #s locked is it

mowens

#2
May 12, 2021, 07:52 AM Last Edit: December 31, 1969, 04:00 PM by Guest
I don't know.
"I would gladly risk feeling bad at times if it also meant that I could taste my dessert." - Data

HTM01

#3
May 12, 2021, 09:52 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: mowens post_id=10961 time=1620831170 user_id=74I don't know.


see if there is a setting to unlock

pmartin

#4
May 12, 2021, 10:23 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: HTM01 post_id=10972 time=1620838334 user_id=76
Quote from: mowens post_id=10961 time=1620831170 user_id=74I don't know.


see if there is a setting to unlock


It may be in parameters as opposed to in settings as on a haas.

Shazam/TPP

#5
May 12, 2021, 12:00 PM Last Edit: December 31, 1969, 04:00 PM by Guest
are there separate folder locations as on a 31i? our Robodrills have a system folder and user folders (31i control)
:sofa:  :cheers:

Tim Johnson

#6
May 19, 2021, 09:25 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: mowens post_id=10958 time=1620829567 user_id=74CGTech has asked me to send them a sub program that our machine uses but I can't find it. The control is a heavily modified Fanuc 30i control. I can find a backup copy on the PC side but not the current program. It was well over 20 years ago the last time I delved into the control itself and I'm a little lost.
Any suggestions?


Who would normally load the programs and subprograms into the control?
FJB

Tim Johnson

#7
May 19, 2021, 09:27 AM Last Edit: December 31, 1969, 04:00 PM by Guest
[quote="Tim Johnson" post_id=11320 time=1621441505 user_id=68]
Quote from: mowens post_id=10958 time=1620829567 user_id=74CGTech has asked me to send them a sub program that our machine uses but I can't find it. The control is a heavily modified Fanuc 30i control. I can find a backup copy on the PC side but not the current program. It was well over 20 years ago the last time I delved into the control itself and I'm a little lost.
Any suggestions?


Who would normally load the programs and subprograms into the control?

Are you drip feeding the programs from another source?
FJB
Go Up Pages1