3D model of a manual horizontal/vertical indexing chuck table?

Started by neurosis, February 18, 2021, 07:14 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Go Down Pages1 2

neurosis

February 18, 2021, 07:14 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Anyone know where to get a 3d model of one of these things?  It's mostly for visual aid for setup sheets so not looking for something spectacular.  


">
I'll go back to being a conservative, when conservatives go back to being conservative.

RobertELee

#1
February 18, 2021, 07:22 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Have you checked the manufacturers or sellers website? Some have downloadable models.

neurosis

#2
February 18, 2021, 07:48 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: RobertELee post_id=7031 time=1613661752 user_id=55Have you checked the manufacturers or sellers website? Some have downloadable models.


I'm not even sure who makes these things anymore.  The table that we have is an old Westinghouse.  This thing is probably older than I am.  

I've been able to find some old drawings for some of these tables but they are very vague.

I looked on GrabCad, but they don't appear to have anything on there.
I'll go back to being a conservative, when conservatives go back to being conservative.

RobertELee

#3
February 18, 2021, 08:09 AM Last Edit: December 31, 1969, 04:00 PM by Guest
OIC... yeah if it's that old then I'd say your best option is to draw one up. Unless of course you get lucky and find a model that's close enough on a model sharing site. But it may just be quicker and easier to draw one up.

Rstewart

#4
February 18, 2021, 05:04 PM Last Edit: December 31, 1969, 04:00 PM by Guest
12" dial caliper and a Tape measure!  Git yur lazy tail out to the shop and measure it   :lol:  :lol:

RobertELee

#5
February 18, 2021, 05:12 PM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: Rstewart post_id=7064 time=1613696644 user_id=6312" dial caliper and a Tape measure!  Git yur lazy tail out to the shop and measure it   :lol:  :lol:



Or stay lazy and hand the indexer off to the QC guy and have him plot it out on the CMM  :thumbsup:

neurosis

#6
February 19, 2021, 08:25 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: RobertELee post_id=7066 time=1613697171 user_id=55Or stay lazy and hand the indexer off to the QC guy and have him plot it out on the CMM  :thumbsup:


Yes, I'm going to have to get off of my lazy butt and draw it up.  :D  

We have a few models of different chucks so the hard part is done.
I'll go back to being a conservative, when conservatives go back to being conservative.

Matthew Hajicek

#7
February 19, 2021, 10:10 AM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: RobertELee post_id=7066 time=1613697171 user_id=55Or stay lazy and hand the indexer off to the QC guy and have him plot it out on the CMM  :thumbsup:


You guys have a CMM?  I'm so jelly.  We have to inspect bone plates with calipers and a tool scope.

Rstewart

#8
February 20, 2021, 03:07 PM Last Edit: December 31, 1969, 04:00 PM by Guest
[quote="Matthew Hajicek" post_id=7101 time=1613758204 user_id=57]
Quote from: RobertELee post_id=7066 time=1613697171 user_id=55Or stay lazy and hand the indexer off to the QC guy and have him plot it out on the CMM  :thumbsup:


You guys have a CMM?  I'm so jelly.  We have to inspect bone plates with calipers and a tool scope.
[/quote]

So you're basically working in conceptual all the time?

Matthew Hajicek

#9
February 20, 2021, 05:01 PM Last Edit: December 31, 1969, 04:00 PM by Guest
Quote from: Rstewart post_id=7215 time=1613862450 user_id=63So you're basically working in conceptual all the time?


Nope, just faking it.

"If you can't inspect it, it's not a critical dimension."

Rstewart

#10
February 20, 2021, 06:15 PM Last Edit: December 31, 1969, 04:00 PM by Guest
[quote="Matthew Hajicek" post_id=7217 time=1613869281 user_id=57]
Quote from: Rstewart post_id=7215 time=1613862450 user_id=63So you're basically working in conceptual all the time?


Nope, just faking it.

"If you can't inspect it, it's not a critical dimension."
[/quote]

 :rofl:  :rofl:

byte

#11
February 21, 2021, 04:39 AM Last Edit: December 31, 1969, 04:00 PM by Guest
[quote="Matthew Hajicek" post_id=7101 time=1613758204 user_id=57]
Quote from: RobertELee post_id=7066 time=1613697171 user_id=55Or stay lazy and hand the indexer off to the QC guy and have him plot it out on the CMM  :thumbsup:


You guys have a CMM?  I'm so jelly.  We have to inspect bone plates with calipers and a tool scope.
[/quote]

If you have an IPhone, I heard they have can do mean 3D scanning with the camera,
Haven't tried it myself.

gcode

#12
February 21, 2021, 11:25 AM Last Edit: December 31, 1969, 04:00 PM by Guest
I spent half a lifetime running one of these back in my manual machinist days
I didn't have any luck finding a model though

https://www.penntoolco.com/yuasa-accu-dex-rotary-indexers-super-spacers/">//https://www.penntoolco.com/yuasa-accu-dex-rotary-indexers-super-spacers/

Dan_AKA_ROY23

#13
February 23, 2021, 12:30 PM Last Edit: December 31, 1969, 04:00 PM by Guest
Looks like a fun design..

Hardmill

#14
February 23, 2021, 08:01 PM Last Edit: December 31, 1969, 04:00 PM by Guest
Found this online :

">

Message me your email if you want it





















PEACE :D
Go Up Pages1 2