wind

[Incogneeto]

I've never been big on the Mustang aside from the old '69 Boss 429, but have you seen the Mustang GTD?
That thing is insane.
800hp.

Oops !! There goes a good chunk of my Lotto Money!!

[Jeff]

Oops !! There goes a good chunk of my Lotto Money!!

$300k of it!

[Incogneeto]

$300k of it!

"Why Buy One when you can have Two at Twice The Price."  

[SuperHoneyBadger]

Mustang GTD?
That thing is insane.

Thats pretty cool, I have to say.

[ghuns]

$300k of it!

They are making it in Kanardia. Don't forget to add 25% for the tariff.

Wanna see the coolant expansion tank for one? We built the mold for it. One of the top 5 nastiest molds I've ever dealt with...

[Incogneeto]

They are making it in Kanardia. Don't forget to add 25% for the tariff.

Wanna see the coolant expansion tank for one? We built the mold for it. One of the top 5 nastiest molds I've ever dealt with...

I love it.

How did you deal with the Threads.??

Did you use a rack ?

[ghuns]

I love it.

How did you deal with the Threads.??

Did you use a rack ?

Slides/lifters. No unscrewing needed.

The worst part are the two ports on the bottom. They are not on the same angle. If you extend their centerlines outward they will intersect. But we had to come up with a way to pull them using only one hydraulic cylinder. It's dicey. But it's a very low volume part, so what the hell.

[Del.]

They are making it in Kanardia. Don't forget to add 25% for the tariff.

Wanna see the coolant expansion tank for one? We built the mold for it. One of the top 5 nastiest molds I've ever dealt with...

All molds are nasty. " Let's design something that's near impossible to make without a straight line anywhere and give someone 3 weeks to make it" 😝

[Incogneeto]

Slides/lifters. No unscrewing needed.

The worst part are the two ports on the bottom. They are not on the same angle. If you extend their centerlines outward they will intersect. But we had to come up with a way to pull them using only one hydraulic cylinder. It's dicey. But it's a very low volume part, so what the hell.

I can see the difference in the angle But I cant see the ejector points.

My Bad was this a four point slide?

It's Intense shit!!

[Incogneeto]

All molds are nasty. " Let's design something that's near impossible to make without a straight line anywhere and give someone 3 weeks to make it" 😝

LOL!! On Average we were 16 to 48 weeks.

Mind you this was all Manual. No CNC.

"0" Flash Medical.

I've forgotten more than I remember.

[Del.]

LOL!! On Average we were 16 to 48 weeks.

Mind you this was all Manual. No CNC.

"0" Flash Medical.

I've forgotten more than I remember.

I bet they asked at the 4 week mark " are you about done "?

[Incogneeto]

I bet they asked at the 4 week mark " are you about done "?

When I was young I said "Yessir"

When I was older I said "Fuck you It's done when It's Done"

[Del.]

I just saw a post on FB where someone posted a pic of a drift for tapered shanks. He found it in his dad's old toolbox and wanted to know what it was. A guy responded " It's a Kentucky toothpick ". 😂

[Del.]

When I was young I said "Yessir"

When I was older I said "Fuck you It's done when It's Done"

I always said " In about an hour "

[ghuns]

I can see the difference in the angle But I cant see the ejector points.

My Bad was this a four point slide?

It's Intense shit!!