Industrial

Shrink fit system

Started by mayday

Replies: 5
Views: 1,759

February 19, 2023, 10:41 AM
by mkd

Robots for trimming molded composites and plastic shapes

Started by mattq

Replies: 1
Views: 1,109

July 01, 2024, 07:41 PM
by CNCAppsJames

Need someone to make some very tight tolerance 5 axis or Swiss parts.

Started by Matthew Hajicek

Replies: 7
Views: 1,706

May 30, 2021, 09:24 AM
by mayday

Tumble Blaster?

Started by Matthew Hajicek

Replies: 6
Views: 1,841

January 07, 2021, 02:22 PM
by Matthew Hajicek

VR CADCAM

Started by Matthew Hajicek

Replies: 0
Views: 1,112

February 10, 2021, 03:18 PM
by Matthew Hajicek

Ti Roughing, Low Rigidity Setup?

Started by Matthew Hajicek

Pages1 2

Replies: 18
Views: 2,644

February 19, 2021, 10:24 AM
by Matthew Hajicek

Dynamic Roughing Improvements?

Started by Matthew Hajicek

Replies: 4
Views: 1,891

July 26, 2022, 06:00 AM
by gcode

TRT70 Progress

Started by Matthew Hajicek

Replies: 3
Views: 1,341

January 06, 2023, 11:13 AM
by gcode

Mazak opinions?

Started by marshal

Pages1 2

Replies: 22
Views: 3,639

May 11, 2021, 08:19 AM
by HTM01

Setup tool manager

Started by Mads Riis

Replies: 1
Views: 1,180

May 04, 2023, 02:42 AM
by JParis

Solid Modeling Recommendation (long read)

Started by Leehound

Pages1 2

Replies: 20
Views: 3,146

October 12, 2021, 02:15 PM
by byte

Can you bend a solid model?

Started by Leehound

Replies: 7
Views: 2,092

June 28, 2024, 08:32 PM
by Brian

A new machining technique. Over 30 years in this trade, learn something new.

Started by Leehound

Replies: 10
Views: 2,575

April 28, 2022, 05:29 AM
by Jim at Gentex

Whats Been Your Experience - Upgrading to Windows 11?

Started by Leehound

Replies: 12
Views: 2,418

September 20, 2025, 10:15 PM
by Newbeeee™

Where to find Solid Models?

Started by Leehound

Replies: 5
Views: 1,701

February 07, 2024, 02:41 PM
by Leehound

Haas Spindle C Axis Drive

Started by kccadcam

Replies: 2
Views: 1,169

June 11, 2025, 03:13 PM
by TSmcam

ModuleWorks Announces GPU Simulation

Started by kccadcam

Pages1 2

Replies: 29
Views: 3,721

September 19, 2025, 06:19 AM
by Dylan Gondyke

Vericut Optimzer

Started by kccadcam

Pages1 2

Replies: 17
Views: 4,147

October 24, 2024, 11:13 AM
by mkd

Synchro tapping heads

Started by kccadcam

Replies: 2
Views: 1,091

January 17, 2023, 10:01 AM
by MIL-TFP-41

2021 Optirough vs. Optirest

Started by kccadcam

Replies: 13
Views: 3,032

February 20, 2021, 04:21 PM
by gcode